English
Español
Deutsch
日本語
Français
中國
한국의
Українська
Italiano
Nederlands
Türkçe
Português
Bahasa Indonesia
Русский
हिंदीwoman body for vase mode Model do druku 3D
Treści, które za chwilę obejrzysz, mogą zawierać materiały przeznaczone wyłącznie dla osób dorosłych. Aby kontynuować, musisz potwierdzić, że masz co najmniej 18 lat.
Tak, mam co najmniej 18 lat
- Dostępne formaty: Stereolithography: stl 16.61 MB
- Kolekcja:No
- Gotowy do wydruku:
- 3D Scan:No
- Adult content:
- PBR:No
- Liczba wyświetleń:4691
- Data: 2021-03-15
- ID produktu:341135
- Oceny:
highly optimised version to be printed easily and faster in vase mode!
recommended settings with 0.4 mm nozzle:
optimisations:
head cut at a greater angle for better overhang
slightly lower shoulders for better overhang
reduced pit above the clavicle
adding venetian dimples
most proportioned body
increased definition between the legs and the buttocks
fixed the hole between legs
3d printing settings
cura: special modes -> spiralize outer contour
s3d: layer -> single outline (vase mode)
slic3r: print setting -> spiral vase
no support!
50% size ( 30 minute):
layer height: = 0.10 - 0.11 mm
line width/extrusion width: 0.55*
speed: 30 mm/sec or slower! (20 mm/sec wall)
minimum layer time: 3s
temperature: +5c
fan: 75%**
100% size (90 minute):
layer height: 0.12 - 0.13 mm
line width/extrusion width: 0.65*
speed: 40 mm/sec or slower! (25 mm/sec wall)
minimum layer time: 6s
temperature: +10 c°
fan: 75%**
200% size (230 minute):
layer height: 0.16 - 0.17 mm
line width/extrusion width: 0.8*
speed: 50 mm/sec or slower! (30 mm/sec wall)
minimum layer time: 10s
temperature: +15 c°
fan: 75%**
*yes, it is possible to change the width of the line, up to 0.8 mm even with a nozzle from 0.4 mm
**only for pla and for better interlayer adhesion, but if the overhang are wrong, increased to 100 as well. (petg 100%, abs 0%)
Czytaj więcejrecommended settings with 0.4 mm nozzle:
optimisations:
head cut at a greater angle for better overhang
slightly lower shoulders for better overhang
reduced pit above the clavicle
adding venetian dimples
most proportioned body
increased definition between the legs and the buttocks
fixed the hole between legs
3d printing settings
cura: special modes -> spiralize outer contour
s3d: layer -> single outline (vase mode)
slic3r: print setting -> spiral vase
no support!
50% size ( 30 minute):
layer height: = 0.10 - 0.11 mm
line width/extrusion width: 0.55*
speed: 30 mm/sec or slower! (20 mm/sec wall)
minimum layer time: 3s
temperature: +5c
fan: 75%**
100% size (90 minute):
layer height: 0.12 - 0.13 mm
line width/extrusion width: 0.65*
speed: 40 mm/sec or slower! (25 mm/sec wall)
minimum layer time: 6s
temperature: +10 c°
fan: 75%**
200% size (230 minute):
layer height: 0.16 - 0.17 mm
line width/extrusion width: 0.8*
speed: 50 mm/sec or slower! (30 mm/sec wall)
minimum layer time: 10s
temperature: +15 c°
fan: 75%**
*yes, it is possible to change the width of the line, up to 0.8 mm even with a nozzle from 0.4 mm
**only for pla and for better interlayer adhesion, but if the overhang are wrong, increased to 100 as well. (petg 100%, abs 0%)
Potrzebujesz plik w innym formacie?
Jeśli potrzebny Ci plik w innym formacie, zgłoś taką potrzebę przez opcję Support Ticket Konwertujemy produkty na następujące formaty: .stl, .c4d, .obj, .fbx, .ma/.mb, .3ds, .3dm, .dxf/.dwg, .max. .blend, .skp, .glb. Nie konwertujemy scen 3D oraz formaty takie jak .step, .iges, .stp, .sldprt.!
Jeśli potrzebny Ci plik w innym formacie, zgłoś taką potrzebę przez opcję Support Ticket Konwertujemy produkty na następujące formaty: .stl, .c4d, .obj, .fbx, .ma/.mb, .3ds, .3dm, .dxf/.dwg, .max. .blend, .skp, .glb. Nie konwertujemy scen 3D oraz formaty takie jak .step, .iges, .stp, .sldprt.!
Pobierz woman body for vase mode Model do druku 3D stl Od 3dinium
art body female figure girl human sculpture sexy vase woman spiral breast vasemode spiralize singleoutline spiralvase tits buttsBrak komentarzy dla tego produktu.
